BMW Siemens MS42 · Serien-Firmware 0110C6
MS42 map switch
Three slots on the stock 0110C6 firmware
- Choose ECU
- Check file
- Pay
- Download
What the patch does
The map switch sits directly on the stock 0110C6 software, no custom firmware needed. The patch places two additional calibration sets in the free flash and hooks into the firmware’s accesses. Slot 1 stays untouched — exactly the calibration the file arrived with, your risk-free way back. Slots 2 and 3 start as copies of it and are calibrated by you in TunerPro.
The three slots
Stock / fallback
Unchanged: the calibration you uploaded. After flashing, the car drives exactly as it did before.
Stage 1
Starts as a copy of slot 1. Your everyday setting — overrun, ignition and injection all freely calibratable.
Stage 2
A second free set. Typically the loud overrun setting, or a gentle one with ignition pulled back.
Switchable per slot
- Full-load ignition — RON91 and RON98 separately
- Full-load injection time, bank 1 and bank 2 separately
- Overrun ignition (ip_iga_pu) — the basis for pops and bangs
- Ignition during overrun cut, also with the A/C switched on
- Overrun cut-off rpm — separately with the A/C switched on
- Overrun VANOS targets, intake and exhaust, two temperature ranges
What you need
- Original files only, exactly as the ECU left the factory: no tuning and no added patches. EWS-off, and launch control and ignition cut from the community patch list, are allowed.
- It must be a fresh full read from your own car, complete and including the bootloader section. A partial read without that section is not enough.
- No bins from the internet. Files from MS4X, forums, collections or file swaps are not supported — they come from a different vehicle, are often already modified, and will not work on your ECU.
- An MS4x tool to correct the checksum and write the full flash — the shop deliberately does not calculate the checksum.
- TunerPro to calibrate slots 2 and 3.
Specifications
Questions about this product
How do I switch slots in the car?
Only while stationary with the engine off and the ignition on. Press and hold the brake for about five seconds — the tachometer needle jumps to the active slot, showing the switch is armed. Release the brake, then press the throttle down and let go: that steps one slot further, 1000 rpm = slot 1, 2000 = slot 2, 3000 = slot 3. A short brake press confirms; after about half a minute without input it ends by itself. As soon as the engine runs or the car rolls, the switch is inactive.
Does the chosen slot stay after ignition off?
Yes, as long as the battery stays connected. After disconnecting the battery the ECU starts safely in slot 1.
Does it work together with launch control or ignition cut?
Yes. Launch control and ignition cut from the community patch list are accepted if they are already on your file, and so is EWS-off. Other added patches are rejected by the check.
Why does the file have to be stock?
The patch identifies the stock software by fixed byte patterns and writes into areas that are empty in stock files. An existing tune or another map switch has changed both. The check rejects such files rather than quietly overwriting something — that would be the shortest path to a dead ECU.
Why does slot 1 stay unchanged?
So there is always a state in which the car runs on exactly the calibration it had before flashing. New calibrations belong in slot 2 or 3; switching back works while stationary, without flashing.
Can I pass the file on to a friend?
No. Every file is created for exactly one vehicle and only runs there. A second car needs a second purchase.
Does the shop calculate the checksum?
No, deliberately not. The bin leaves the shop uncorrected; you fix the checksum with the MS4x tool you also flash with.
What does an update cost?
Nothing. Simply upload your bin again: the shop recognises you and releases the download without payment.